← Back to NASA Technology Projects
Completed TRL 4 (started at 4, targeting 6)
It is proposed to produce a piezoelectric carbon nanotube based structural health monitoring (SHM) system. Basically this will be carbon nanotubes and lead zirconium titanate (PZT) nanopowders dispersed in a PVDF-TrFE polymer matrix. These sensors will be flexible and can be integrated between plies as well as adhered to the structure surfaces. It is planned to 3-D print these sensors using an nScrypt 3-D printer. Once printed, heating to remove any solvent and transform the PVDF-TrFE to the piezoelectric beta phase will treat the sensor. Samples will be poled using corona poling and hysteresis curves generated. Samples will also be embedded within plies of composite bend specimens and curves of voltage response versus strain generated. In the past year working off of CIF funding we have produced 3-D printed sensor materials from the above materials which show excellent piezoelectric properties as well as pyroelectric properties. In the proposed research we will optimize the properties of the sensor material and 3-D print and test a wireless antenna on the sensor. Owing to the pyroelectric nature of the material we will also test a wireless system as a heat sensor.
The use of composite structures in aerospace and space applications is growing each year. Since composites are inherently brittle materials it is important to monitor the structural health of these structures. Presently strain gauges and fiber optic strain sensors are used. Both types of sensors are brittle and can themselves fail. Neither can be used during flight to continuously monitor structural health.
It is proposed to 3-D print SHM sensors for use in composite structures. The first step will be to disperse carbon nanotubes and PVDF-TrFE polymer in dimethyl formamide (DMF) solvent.
Dispersion will be aided by the appropriate dispersant. This solution will be thoroughly mixed at 60C until the carbon nanotubes are totally dispersed. Next lead zirconium titanate nanopowders will be added and mixed until a uniform mixture is obtained. Lead zirconium titanate had the highest piezoelectric response of any material. When cured PVDF-TrFE forms a piezoelectric beta phase. In this composite sensor, the PVDF-TrFE and lead zirconium titanate yield the piezoelectric properties while the carbon nanotubes add structural strength. The random distribution of carbon nanotubes and lead zirconium titanate will ensure a flexible structure. On a previous CIF the PI found adding barium titanate nanopowders to PVDF-TrFE increased the piezoelectric response of the composite material. Once a suitable viscosity is obtained for the solution (~ 20,000 cP) sensors will be 3-D printed using our nScrypt 3-D printer.
The sensors will be printed on glass plates, then cured in a vacuum furnace at 150C. We will print thicknesses from 10 microns up to 500 microns. Our printer had the capability to print up to an area of 1 square foot, so we have latitude in the size of sensors we will be able to print. The piezoelectric effect will be tested at AMRDEC’s Weapon’s Laboratory. They will first be corona poled in order to align the dipoles in the PVDF-TrFE, then hysteresis curves will be generated from which piezoelectric constants can be obtained. Then a formulation, which yields a consistent piezoelectric response, sensors, will be produced which can be attached to the surface of a composite and also between plies. In both cases, composite bend specimens will be produced, the sensor applied, the testing in bending mode. While the bending test is ongoing, voltage response will be measured in order to generate a response curve of voltage versus stress.
Finally, wireless antennae will be produced. This antenna can be directly printed on the sensor yielding a SHM sensor, which can be used from manufacture through flight. Shown below is a 3- D printed composite sensor produced this past year along with the piezoelectric hysteresis curve as well as the hysteresis curve for this sample.
For this program Dr. Dennis S. Tucker will act as the principle investigator. Dr. Tucker has 10 years of experience in the production of carbon nanotube composites for structural and piezoelectric applications. Mr. Curtis Hill will be co-investigator for this project. He has over 30 years of experience with chemical processing and their applications. He is also the operator for the nScrypt 3-D printer. We will also utilize nScrypt Inc. for their 3-D printing expertise gratis.
Listed on TechPort itself — the most direct way to ask about this specific project.
This is early/mid-stage (TRL 4) — the most realistic path in is NASA SBIR/STTR, which funds small businesses and research institutions to develop technology aligned with NASA's needs (equity-free, phased funding). Check whether a current SBIR/STTR solicitation topic overlaps with this project's technology area, or contact the project directly (above) to ask.
None of these are guaranteed paths for this specific project — TechPort itself doesn't have an "apply" button. Reaching out to the contact(s) above with a specific question is usually the fastest way to find out what's actually open.